Multi-Timer Dashboard
Three independent countdown timers running simultaneously — perfect for workshops, panels, and Q&A sessions.
Three independent countdown timers running simultaneously — perfect for workshops, panels, and Q&A sessions.
A multi-timer puts several independent countdown timers on one screen, each with its own duration, controls, and alert. Instead of juggling a phone timer, a kitchen timer, and a clock, you can watch every countdown side by side and see at a glance which one finishes next. This dashboard provides three timers that can run at the same time or one after another.
Multiple timers help whenever activities overlap but end at different times. A panel moderator might track total session time, the current speaker's time, and the Q&A segment. A trainer might run three breakout groups with different task lengths. Teachers, coaches, and home cooks use the same setup. The key is labeling each timer's job before you start, and choosing durations that leave a buffer, so the alerts do not all land within a few seconds of one another. Keeping all three on one visible screen also avoids missed alerts from devices left in another room.
To use the multi-timer, set the Min and Sec fields for Timer 1, Timer 2, and Timer 3; they start at 10, 5, and 2 minutes. Each timer has its own Start (▶), Pause (⏸), and Reset (↺) buttons, a large display, and a progress bar that shrinks as time runs out. Starting, pausing, or resetting one timer does not affect the others. When a timer reaches zero it stops and plays a short beep. Durations longer than an hour work too; entering 90 minutes, for example, displays as 1:30:00. Changing a timer's fields while it is stopped resets it to the new duration.
Decide what each timer represents before starting, then enter the durations. For a 45-minute panel with three speakers, set Timer 1 to 45 minutes for the whole session, Timer 2 to 8 minutes for the current speaker, and Timer 3 to 10 minutes for Q&A. Start Timer 1 at the opening, restart Timer 2 for each speaker, and start Timer 3 when questions begin.
Staggered starts work well when tasks must finish together: if one task needs 25 minutes and another needs 10, start the 25-minute timer first and the 10-minute timer when the first shows 10:00 remaining.
Example multi-timer setups
| Situation | Timer 1 | Timer 2 | Timer 3 |
|---|---|---|---|
| Panel discussion | 45 min session | 8 min per speaker | 10 min Q&A |
| Workshop breakouts | 15 min Group A | 20 min Group B | 25 min Group C |
| Training session | 50 min block | 10 min break | 5 min recap |
| Interview day | 30 min interview | 10 min debrief | 5 min reset |
| Kitchen | 45 min roast | 20 min side dish | 12 min pasta |
| Classroom stations | 12 min station 1 | 12 min station 2 | 12 min station 3 |
Set the duration for each timer using the minute and second fields. Press Start on each timer when ready. Each timer counts down independently.
The Pause button stops that individual timer. The Reset button returns it to its starting duration. Audio alerts play for each timer independently when it reaches zero.
Yes — each timer is completely independent. Start, pause, and reset each one separately without affecting the others.
Yes — each timer plays an audio alert when its countdown finishes, independently of the other timers.
Panel discussions with multiple speakers, workshops with simultaneous group activities, cooking multiple dishes with different timing, or managing multiple tasks with separate deadlines.
Yes — each timer has its own minutes and seconds inputs. Set them independently before starting.
This dashboard has three timers. For a fourth or fifth countdown, open the page in a second browser tab — each tab runs its own set of timers independently.
The running countdown keeps going with its original duration. Press Pause and then Reset (↺) to load the new minutes and seconds.
No. Each timer stops at 00:00 and plays a short beep. Press Start again to rerun the same duration.
Enter the total in the Min field — for example, 90 for an hour and a half or 120 for two hours. The display switches to hours, minutes, and seconds, such as 1:30:00.